Process Equipment & Plant Design Mcqs for Chemical

Q.  Smaller sized packings are generally dumped to the packed columns, and the large ones of size greater than ______________ mm are stacked individually, which provides better control over bed porosity and offers lower gas pressure drop?

a. 25
b. 50
c. 75
d. 150


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  In packed absorption tower, onset of flooding usually occurs at a pressure drop of about ______________ mm of water column per metre height of packing?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Diameter of bubble caps used in high pressure columns is ______________ as compared to that used in identical vacuum columns?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Shell side heat transfer co-efficient in case of square pitch as compared to the triangular pitch under similar condition of fluid flow and tube size is_____________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A riveted joint does not fail by _____________________ of rivets?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger, the ‘tube pitch’ is defined as the _____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  25 per cent cut segmental baffle means that the baffle__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For a cylindrical vessel of moderate height, the weld joint efficiency for joints parallel to the cylindrical axis is given as 1.0; while for joints along the girth (circumference) it is given as 0.8. In calculating the shell wall thickness using code formula for an internally pressurised cylindrical vessel, what value of weld joint efficiency should be used ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Of the pressure vessels, with same thickness but different diameters, which one withstands higher pressure ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Generally, as the length of the liquid path on a tray is increased beyond 5 ft, the overall column efficiency___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For high pressure process equipments/vessels, the connected nozzle should be____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Back-trapping in a distillation column results due to_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement about the design of sieve plate column and the bubble cap column ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The function of manholes provided in the shell of a distillation column is to __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Height of the flights in the rotary drier is in the range of___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Corrosion allowance in the design of pressure vessel/chemical equipment is not necessary, if___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Column support for the roof of cylindrical storage tank must be provided for___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The stress developed in a material without any permanent set is called the____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following material is seldom used for pressure vessel construction ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For laminar flow (NRe < 2100) in steel pipe, the optimum inside pipe diameter is given by____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Correct use of ‘factor of safety’ is very important in equipment design. It is defined as the ratio of the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts