Process Control & Instrumentation Mcqs for Chemical


Q.  Silver point temperature is ______________ °C?

a. 760.5
b. 860.5
c. 960.5
d. 1060.5


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Water is entering a storage tank at a temperature T0 and flow rate Q0 and leaving at a flow rate Q and temperature T. There are negligible heat losses in the tank. The area of cross-section of the tank is A0. The model that describes the dynamic variation of temperature of water in the tank with time is given as________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The transfer function for a P-D controller is________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The time constant of a unity gain, first order plus time delay process is 5 min. If the phase lag at a frequency of 0.2 rad/min is 60°, then the dead time (in minutes) is________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Dead zone is the__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  All the thermocouples used for temperature measurement use dissimilar metal ________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  A non-linear chemical system is exemplified by a/an_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Continuous flue gas analyser makes use of paramagnetic properties of some of its constituents, which move towards the strongest part of the magnetic field thus displacing diamagnetic gases. Which of the following gases is diamagnetic ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Phase margin is equal to_______________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  For the time domain function f(t) = t, the Laplace transform of ∫0 t f(t) dt is given by___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Thermocouple is suitable for measuring_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The frequency at which maximum amplitude ratio is attained is called the ______________ frequency?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The time taken for a radioactive element to reduce to 50% of its original weight is _____________ years, if its half life period is 12 years?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Pick out the wrong statement?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Pick out the wrong statement ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Select the correct statement from the following?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Pick out the first order system from among the following ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Pick out the one which is a first order instrument ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  What is the value of ‘q’ for saturated vapor feed to a distillation column? (where q = fraction of the feed stream that is liquid ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Large process vessels operating under extreme temperature and pressure conditions are normally clad/ lined with materials like stainless steel, aluminium, nickel & its alloys, copper & its alloys and titanium. The cladding thickness is generally about ______________ percent of the total thickness?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Pick out the wrong statement pertaining to the design of a horizontal tube evaporator ?
Category: Chemical Engineering Mcqs,   Published by: teswesm