Theory of Machines Test Questions

Q.  Shaft with taper key is an example of

a. incompletely constrained motion
b. completely constrained motion
c. successfully constrained motion
d. all of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  What are crank effort diagrams?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following statements is/are true?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which clutch is known as wet clutch?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  In centrifugal clutches, when is the contact between shoe friction lining and surface of drum observed?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Calculate torque transmitted by the clutch having four shoes, which has spring force of 700 N and centrifugal force of 4000 N. Rim diameter is 560 mm and coefficient of friction is 0.3
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  If brakes are applied on front wheels of a car and if it moves on a level road, then retardation of the car is calculated using the formula
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Determine the power transmitted if dead weight on brake is 70 kg and engine has a speed of 300 rpm. One end of the rope has a diameter of 0.05 m is attached to a spring balance which has reading of 150 N, diameter of drum is 1 m.
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which parameters can be measured using a dynamometer?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Identify the type of absorption dynamometer ?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following statements is/are false?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  In a Hooke's joint, maximum velocity ratio between driving and driven shaft is possible if θ is
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which relation is used to denote condition for equal speeds, when driving and driven shafts are connected by Hook's joint?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Calculate the angular speed of driven shaft if the driving shaft has angular speed of 400 rpm. When shaft angle is 20° and angle of rotation is 40° in Hooke's joint.
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Calculate the angle of driving shaft, if the two shafts of the Hooke's joint are inclined at an angle of 18.50°
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The relation between number of links and number of lower pairs is given as n = 2p – 4. If L.H.S is less than R.H.S of this equation then the chain is
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  One quaternary joint is equal to how many binary joints?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Watt's mechanism is based on
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Scotch yoke mechanism is the inversion of
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Calculate torque acting on the crank, if tangential force acting on the engine is 150 kN and 300 mm is the crank radius.
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Calculate the thrust in connecting rod, if piston effort is 200 kN and crank makes an angle of 45° from TDC. Assume obliquity ratio = 3.5
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts