Process Control & Instrumentation Mcqs for Chemical


Q.  Select the correct statement from the following?

a. The frequency response of a pure capacity process is unbounded
b. The phase lag of a pure time delay system decreases with increasing frequency
c. The amplitude ratio of a pure capacity process is inversely proportional to frequency
d. The amplitude ratio of a pure time delay system increases with frequency


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Stage efficiency for packed tower varies with the____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Tube wall thickness depends on the corrosiveness of the fluids and their operating pressure & temperature and is specified by Birmingham wire gauge (B.W.G)-a number which varies from 8 to 18 with the numbers 14 and 16 being more commonly used. Outside diameter of tubes varies from about 15 to 50 mm; however a tube of less than _____________ mm outside diameter is generally not recommended for fouling fluids ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In hydrostatic testing of welded pipe (for leakage, strength etc.) the ratio of minimum hydrostatic test pressure to internal design pressure is around __________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In a shell and tube heat exchanger, the shortest centre to centre distance between the adjacent tubes is__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  If ‘D’ is the inside diameter of the shell of a shell and tube heat exchanger, then the baffle spacing is usually in the range of__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  For turbulent flow (NRe > 2100) of low viscosity fluid (μ > 20cp) in steel pipes, the optimum inside pipe diameter is given by(where, Q = fluid flow rate, ft3/sec, ρ = fluid density, lb/ft3 μ = fluid viscosity, centipoise Di = optimum inside pipe diameter, inches) ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Scale up problem in design based on the similarity concept takes into account _______________ similarity?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The longitudinal stress induced in a thin walled cylindrical vessel under internal pressure is_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  1.2 to 3.8 cms is the value of the ______________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In a pressure vessel containing multiple openings of various dimensions at different parts, stress concentration at the edges of the opening is maximum which becomes negligibly small beyond the area covered by ______________ times the hole diameter?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Removable connection of tubes to tube sheet is called___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Bubble cap tray is the most commonly used tray in large distillation column, because______________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  (Le/D) for a Tee (used as elbow, entering run) would be around _______________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  At equal mass velocities, the values of film co-efficients for gases as compared to that for liquids are generally ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the _______________ stress?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Baffles are provided in a shell and tube heat exchanger to increase the turbulence and velocity of the shell side fluid. Which of the following shaped baffles does not fall in the category of transverse baffle ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Value of Peclet number = ∞, is the representative of___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Steam economy is defined as the amount of evaporation per unit amount of steam used, while the capacity is the total evaporation obtained per hour. Use of multiple effects in evaporation ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Value of Peclet number = 0, is the representative of ____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In case of a ‘thin’ pressure vessel, the ratio of its diameter to wall thickness is_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm