Structural Analysis Mcqs

Q.  Principle of superposition is applicable when___________________?

a. deflections are linear functions of applied forces
b. material obeys Hooke’s law
c. the action of applied forces will be affected by small deformations of the structure
d. none of the above


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Maximum shear stress theory for the failure of a material at the elastic limit, is known________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A cantilever of length is subjected to a bending moment at its free end. If EI is the flexural rigidity of the section, the deflection of the free end, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  constant, depth of a cantilever of length of uniform strength loaded with Keeping breadth uniformly distributed load varies from zero at the free end and________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The force in BC of the truss shown in the given figure, is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The degree of indeterminacy of the frame in the given figure, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A simply supported beam A carries a point load at its mid span. Another identical beam B carries the same load but uniformly distributed over the entire span. The ratio of the maximum deflections of the beams A and B, will be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of a simply supported I-section beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If Ix and Iy are the moments of inertia of a section about X and Y axes, the polar moment of inertia of the section, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If E, N, K and 1/m are modulus of elasticity, modulus of rigidity. Bulk modulus and Poisson ratio of the material, the following relationship holds good_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Gradually applied static loads do not change with time their_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A body is said to be in equilibrium if___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The forces acting normally on the cross section of a bar shown in the given figure introduce_____________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The load on a spring per unit deflection, is called______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A close coil helical spring of mean diameter D consists of n coils of diameter d. If it carries an axial load W, the energy stored in the spring, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The moment of inertia of a triangular section (height h, base b) about its base, is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The assumption in the theory of bending of beams is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A concentrated load P is supported by the free end of a quadrantal ring AB whose end B is fixed. The ratio of the vertical to horizontal deflections of the end A, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum deflection due to a uniformly distributed load w/unit length over entire span of a cantilever of length l and of flexural rigidly EI, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The forces acting normally on the cross section of a bar shown in the given figure introduce_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts