Process Equipment & Plant Design Mcqs for Chemical

Q.  Power required for agitation depends upon the______________________?

a. Height & properties of the liquid
b. Agitator type & speed of agitation
c. Size of agitator & the tank
d. All A., B. and C.


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  For a 25 mm hole drilled in plates to be riveted, the shank diameter of the rivet should be _______________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of the largest load in a test to the original cross-sectional area of the test specimen is called the _____________ stress?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Factor of safety (i.e., overdesign factor) in heat transfer equipments is about _____________ percent more than the actual/theoretical design factor?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Wind load consideration in the design of a support can be neglected, when the vessel is___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Heat transfer co-efficient for a horizontal condenser as compared to a vertical condenser operating under similar conditions is_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For identical operating conditions, the pressure drop over _______________ tray is the highest out of the following?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger having square pitch, the shell side equivalent diameter is given by (where, P = pitch, d = outside diameter of the tube) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the allocated cap area, bubble caps are generally arranged on equilateral triangular pitch. Number of caps fixed on a plate is with a __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Baffle spacing is generally _________________ the I.D. of the shell ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The dust collection efficiency of a cyclone separator_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Log mean temperature difference in case of multi-pass shell and tube heat exchanger is always_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In distillation columns, bubble caps are held in place over trays by ________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The necessary wall thickness for a metallic storage vessel is a function of the ___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Cylindrical shell thickness of rotary drier is generally _______________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The length of straight rectangular weir used on cross-flow trays is generally ________________ the column diameter ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger, the clearance of the tube is generally___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Frame thickness in the plate and frame filter press is normally in the range of ______________ inches?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of saddle packing (e.g., berl and intralox saddles), the maximum size of the packing should not exceed ______________ of the column diameter?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  At the following point for a given packing and set of fluids, the pressure drop per metre of packed height, with variation in fluid rates and operating pressure____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a double pipe (concentric) heat exchanger, the hydraulic radius for heat transfer (for a fluid flowing through the annulus) would be_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts