Process Equipment & Plant Design Mcqs for Chemical

Q.  Ponchon Savarit method is based on the use of enthalpy concentration diagram, which contains the bubble point curve (saturated liquid curve), dew point curve (saturated vapour curve) and equilibrium tie lines. As compared to McCabe-Thiele’s method, this method_________________?

a. is more accurate in finding the number of equilibrium stages
b. accounts for the enthalpy changes in the process
c. Facilitates direct calculation of heat load on reboiler & condenser from, the diagram used in this method
d. All A, B. & C.


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  To avoid the tearing off the plate of an edge, the margin (i.e., the minimum distance from the centre of the rivet hole to the nearest edge of the plate) should be equal to ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The distance between the centres of a rivet hole to the nearest edge of the plate is called _________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following types of reactors is the safest from operation point of view ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Typical static submergence for bubble cap plate column operating at atmospheric pressure may be around _________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Mc Cable Thiele method used for finding theoretical stages in a distillation column assumes that the_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  (Le/D) for a Tee (used as elbow, entering branch) would be ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A certain pressure vessel manufacturer avoids doing reinforcements calculations for openings by always providing a reinforcing pad extending upto double the diameter of the opening and of the same material and thickness as that of the shell wall. If area compensation is accepted as a code guideline, his approach leads to safe design____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger, the overall heat transfer co-efficient is proportional to the tube side (volumetric flow rate)0.8. This is valid, only when the ratio of the tube side film resistance to the total resistance is almost equal to____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The wall thickness of thin cylindrical shell with hemispherical ends is ______________ that of the spherical ends?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pressure differential maintained across a continuous rotary vacuum filter is in the range of _______________ mm Hg column?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Souders Brown equation given by, U = Kv √(ρl – ρv)/ρv, is used for the calculation of the ______________ in a continuous distillation column?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio for the rate of washing to the final rate of filtration in a washing type of plate and frame filter is____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Optimum economic pipe diameter for fluid flow is determined by the____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For annular flow of a fluid, the ratio of the equivalent diameter for pressure drop calculation to the equivalent diameter for heat transfer calculation is_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Seamless pipe is made________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A minimum clearance of about _______________ mm is maintained between the distillation column wall and the bubble cap?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum acceptable total liquid gradient over a tray is about _______________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Diameter of the sieve tray column is determined by the_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Le/D) for 90° elbow (medium radius) and 90°square elbow would be respectively around___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum plate efficiency is achieved in case of ______________ flow?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts