|
MCQs: The load stress of a section can be reduced by______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: the column head support a flat slab, is generally kept The diameter of_____________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In case the factor of safety against sliding is less than 1.5, a portion of slab is constructed downwards at the end of the heel slab, which is known as___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Lapped splices in tensile reinforcement are generally not used for bars of size larger than______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the width of the foundation for two equal columns is restricted, the shape of the footing generally adopted, is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Minimum spacing between horizontal parallel reinforcement of the same size should not be less than________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For a ribbed slab______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A very comfortable type of stairs is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The width of the flange of a L-beam, should be less than______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2, the beam________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Columns may be made of plain concrete if their unsupported lengths do not exceed their least lateral dimension_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A pre-stressed concrete member is preferred because___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If is the net upward pressure on a square footing of side for a square column of side , the maximum bending moment is given by_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: To ensure uniform pressure distribution, the thickness of the foundation, is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: longitudinal bars and lateral stirrups, is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
