Theory of Structures Mcqs

Q.  Pick up the correct statement from the following ?

a. The moment of inertia is calculated about the axis about which bending takes place
b. If tensile stress is less than axial stress, the section experiences compressive stress
c. If tensile stress is equal to axial stress, the section experiences compressive stress
d. All the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The assumption in the theory of bending of beams is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A concentrated load P is supported by the free end of a quadrantal ring AB whose end B is fixed. The ratio of the vertical to horizontal deflections of the end A, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum deflection due to a uniformly distributed load w/unit length over entire span of a cantilever of length l and of flexural rigidly EI, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The forces acting normally on the cross section of a bar shown in the given figure introduce_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2), 4 mm in diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive load to remove the clearance, is_____________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The strain energy stored in a spring when subjected to greatest load without being permanently distorted, is called______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The strain energy due to volumetric strain________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the truss shown in given figure the force in member DC is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of lateral strain to axial strain of a homogeneous material, is known___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The force in BF of the truss shown in given figure, is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of maximum shear stress to average shear stress of a circular beam, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For a strongest rectangular beam cut from a circular log, the ratio of the width and depth, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  m1 and m2 are the members of two individual simple trusses of a compound truss. The compound truss will be rigid and determinate if__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The greatest load which a spring can carry without getting permanently distorted, is called_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A bar L metre long and having its area of cross-section A, is subjected to a gradually applied tensile load W. The strain energy stored in the bar is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  An isolated load W is acting at a distance a from the left hand support, of a three hinged arch of span 2l and rise h hinged at the crown, the horizontal reaction at the support, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The force in CD of the truss shown in given figure, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of the area of cross-section of a circular section to the area of its core, is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts