|
MCQs: The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The maximum permissible size of aggregates to be used in casting the ribs of a slab, is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: is the pre- stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If C is creep coefficient, f is original pre-stress in concrete, m is modular ratio, E is Young’s modulus of steel and e is shrinkage strain, the combined effect of creep and shrinkage is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: An R.C.C. lintel is spanning an opening of 2 m span in a brick wall. The height of the roof is 2.9 m above the floor level and that of the opening is 2.1 m above the floor level. The lintel is to be designed for self weight plus_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The minimum clear cover for R.C.C. columns shall be_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The design of heel slab of a retaining wall is based on the maximum bending moment due to______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The neutral axis of a T-beam exists_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The minimum thickness of a flat slab is taken_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A pre-cast pile generally used, is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a pre-stressed member it is advisable to use________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Steel bars are generally connected together to get greater length than the standard length by providing_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: mutually perpendicular principal stresses acting on a soil mass, the normal stress If p1 and p2 are________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: carrying a uniformly distributed load per metre length is suspended at two A pile of length points, the maximum, B.M. at the centre of the pile or at the points of suspension, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If is the uniformly distributed load on a circular slab of radius maximum positive radial moment at its centre, is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For M 150 grade concrete (1:2:4) the moment of resistance factor is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The spacing of transverse reinforcement of column is decided by the following consideration_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
