Estimating & Costing Mcqs

Q.  Pick up the correct statement from the following __?

a. In order to check up the average depth of excavation, ‘Dead man s’ are left at the mid-widths of borrow pits
b. The earthwork calculation in excavation is made from the difference in levels obtained with a level
c. The earth work in excavation to form the road embankment includes the formation of correct profile and depositing the soil in layers
d. All the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  the column head support a flat slab, is generally kept The diameter of_____________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case the factor of safety against sliding is less than 1.5, a portion of slab is constructed downwards at the end of the heel slab, which is known as___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Lapped splices in tensile reinforcement are generally not used for bars of size larger than______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the width of the foundation for two equal columns is restricted, the shape of the footing generally adopted, is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum spacing between horizontal parallel reinforcement of the same size should not be less than________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For a ribbed slab______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A very comfortable type of stairs is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The width of the flange of a L-beam, should be less than______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2, the beam________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Columns may be made of plain concrete if their unsupported lengths do not exceed their least lateral dimension_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A pre-stressed concrete member is preferred because___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If is the net upward pressure on a square footing of side for a square column of side , the maximum bending moment is given by_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  To ensure uniform pressure distribution, the thickness of the foundation, is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  longitudinal bars and lateral stirrups, is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum permissible size of aggregates to be used in casting the ribs of a slab, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts