Process Equipment & Plant Design Mcqs for Chemical

Q.  Pick out the wrong statement about the design of sieve plate column and the bubble cap column ?

a. The downcomer design and the residence time in the downcomer is almost same for sieve plate and bubble cap columns
b. Weir length for a bubble cap plate is the same as that for the sieve plate
c. Weir height for a bubble cap plate column is the same as that for a sieve plate column
d. Weir height in case of a bubble cap plate ranges from 50 to 150 mm and is higher than the sieve plate


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  _______________ shaped roof is most commonly used for cylindrical tanks ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The minimum plate spacing in most of the petroleum refinery distillation columns (of dia > 3 ft) is normally _____________ inches?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ____________________ strain is measured using a ‘strain rosetter’ ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the design of a shell and tube heat exchanger, the corrosion allowance ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In packed towers provided with pall rings liquid redistributors are positioned at heights of every 6 metres or 5-10 times the column diameter, whichever is less. Maximum size of the pall rings should not exceed _______________________ of the column diameter?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  With increase in the reflux ratio for a fixed production from a continuous binary distillation column, the ______________________ decreases?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the design of a bag filter, the gas temperature is an important consideration, as it affects the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Longitudinal stress induced in a thin walled cylindrical storage vessel is __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Generally, no corrosion allowance in wall thickness of a part is required, if the thickness is more than ______________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The normal range of velocity of steam in pipes is _________________________ m/sec?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The wall thickness for a large high pressure pipeline is determined by the consideration of the____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Compensation against openings in process vessels for giving inlet and outlet connections, for providing sight glasses and manholes etc. is provided for strength and rigidity. The most efficient type of compensation is of _______________ type?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Hazards associated with the relief valve leakage for extremely hazardous material storage can be taken care of by providing___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Lap joints are preferred for plates having thickness _______________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Thickness of the frame of a plate and frame filter as compared to that of plates is___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Tube side heat transfer co-efficient for turbulent flow of liquid through tubes is proportional to___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A high vapour velocity is required for high plate efficiency in a sieve plate column. The satisfactory value of operating vapor velocity for design purpose in sieve plate column is about _______________ percent of the flooding velocity?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Number of evaporators which can be used in service in a multiple effect evaporation system is limited by the__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The retention time of material in a rotary dryer depends upon its ______________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For given number of passes, pitch & tube diameter, the maximum number of tubes that can be accommodated in a shell of tripled inside diameter will be ____________ times?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts