Mechanical Operations Mcqs for Chemical

Q.  Optimum ratio of operating speed to critical speed of a trommel is_____________________?

a. 0.33-0.45
b. 1.33-1.45
c. 0.5-2
d. 1.5-2.5


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Filter aids like asbestos, kieselguhr, diatomaceous earth etc. are used to increase the porosity of the final filter cake & reducing the cake resistance during filtration. Filter aid is_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Ultracentrifuges running at speeds upto 100000 rpm is normally used for the_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum size reduction in a fluid energy mill is achieved by___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is not a wet classifier ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the _________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Specific surface area is the surface area of a unit _______________ of materials?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Separation of a suspension or slurry into a supernatant clear liquid (free from particles) and a thick sludge containing a high concentration of solid is called__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If a force greater than that of gravity is used to separate solids & fluids of different densities, the process is termed as the __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of the actual mesh dimension of Taylor series to that of the next smaller screen is_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The energy consumed by a ball mill depends on__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Size reduction of asbestos and mica is done by____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of a hammer crusher, the final product size depends on the____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Tube mill compared to ball mill_______________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Tabling process used for separating two materials of different densities by passing the dilute pulp over a table/deck, which is inclined from the horizontal surface at an angle of about________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  To get ultrafine particles, the equipment used is a _________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Kick’s law assumes that the energy required for size reduction is proportional to the logarithm of the ratio between the initial and the final diameters. The unit of Kick’s constant is_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Filtration rate through a filter cake is proportional to (where, S = filtering surface R = specific cake resistance μ = viscosity of the filtrate) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In continuous filtration (at a constant pressure drop), filtrate flow rate varies inversely as the__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The sphericity of a solid particle of cubical shape is ___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  To remove dirt from the flowing fluid, we use a ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts