Process Equipment & Plant Design Mcqs for Chemical

Q.  Normally, the ratio of the total riser area to the tower cross sectional area (for bubble cap towers of diameter more than 3 ft) is around_______________?

a. 0.4-0.6
b. 0.35-0.75
c. 0.1-0.2
d. 0.55-0.85


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  The ratio of shear stress to shear strain is called ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of a shell and tube heat exchanger, the minimum shell thickness for carbon steel (inclusive of corrosion allowance) depends on shell diameter and is in the range of ________________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _____________________ tray arrangement is recommended for distillation column having diameter upto 4 ft ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of bubble cap distillation column of diameter greater than 1.2 metres, the cap diameter is roughly about _______________ cms?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Wall thickness of schedule 40 pipe as compared to that of schedule 80 pipe is ___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Speed of the drum of the rotary vacuum filter normally ranges from _____________ rpm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a continuous distillation column, the optimum reflux ratio ranges from _______________ times the minimum reflux ratio?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The type of stress developed in a metallic bar on subjecting it to a change in temperature without allowing it to be deformed is ______________ stress?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Reflux ratio variation in a distillation column is between___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid/petroleum fuel storage tanks are built underground (as in case of petrol pumps), when the storage capacity is less than ______________ kilolitres?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a heat exchanger, shell side fluid velocity can be changed by changing the tube _______________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Steam side heat transfer co-efficient for design consideration under ordinary condition can be assumed to be about _____________ kcal/hr.m2.°C?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The safe distance of habitation from a hazardous chemical plant (TLV of its product < 1000 ppm) should be about ______________ kms?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of a shell and tube heat exchanger, the effect of L/D on inside film heat transfer coefficient (hi) vanishes after a Reynold number of_____________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  (Le/D) for fully open globe value may be around__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The value of fouling factor depends upon the__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The operating pressure drop range in a bag filter is about ______________ mm water gauge?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following lengths of heat exchanger tubes are normally not used in practice ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In packed absorption tower, onset of flooding usually occurs at a pressure drop of about ______________ mm of water column per metre height of packing?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Diameter of bubble caps used in high pressure columns is ______________ as compared to that used in identical vacuum columns?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts