# Dock & Harbor Engineering Mcqs

Q.  Minimum width of ship clearance shall be__________________?

a. B or 30 m
b. 1.5 B or 50 m
c. 1.5 B
d. 50 m
e. where “B” is beam of the design vessel

ANSWER: See Answer

No explanation is available for this question!
 MCQs:  As per Berlin’s formula, the length of wave in metres is given by_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  In basins subjected to strong winds and tide, the length of the berthing area should not be less than____________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Assertion A : Depth and width required at the entrance to a harbour are more than those required in the channel. Reason R : The entrance to a harbour is usually more exposed to waves as compared to the harbour itself__________________? Select your answer based on the coding system given below. Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The maximum harbour depth below lowest low water is generally equal to_________________? (i) loaded draft + 1.2 m when bottom is rock (ii) loaded draft + 1.8 m when bottom is soft (iii) loaded draft + 1.2 m when bottom is soft (iv) loaded draft + 1.8 m when bottom is rock select the correct the correct statements. Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Dead weight tonnage of a ship_______________? i) varies with latitude and season ii) is more than displacement tonnage iii) is the difference between displacement load and displacement light select the correct statemens. Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Consider the following statements in regard to Beaufort scale for wind speeds______________? (i) The Beaufort number ranges from 1 to 12. (ii) Higher Beaufort number indicates higher speed of wind, (iii) Beaufort number for calm is smallest and for hurricane is highest select the correct statments. Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Assertion A : Basin walls have to be of much grater height than dock walls. Reason R : Tidal basins are subject to fluctuations of levels due to tidal variations? Select your answer based on the coding system given below. Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  If Hs is the significant wave height, then the average wave height and highest wave height respectively are given by_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Consider the following statements? (i) Fender is the cushion provided on the face of the jetty for ships to come in contact, (ii) Slip is the space of water area between two adjacent piers where ships are berthed, (iii) Pier head is a structure constructed near the tip of a break water near the harbour entrance. select the correct statements? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  An airport has 4 gates. If the weighted average gate occupancy time is 30 minutes and gate utilisation factor is 0.5, then the capacity of the gate will be___________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The engine failure case for determining the basic runway length may require________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  If the monthly mean of average daily temperature for the hottest month of the year is 25° C and the monthly mean of the maximum daily temperature of the same month of the year is 46° C, the airport reference temperature is____________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  As per ICAO recommendation, the rate of change of longitudinal gradient per 30 m length of vertical curve for A and B type of airports is limited to a maximum of__________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  As per International Civil Aviation Organization (ICAO) recommendation, minimum width of safety area for instrumental runway should be_________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The minimum width of clearway is_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The total length of a runway is 1000 m. The elevation at distance 0,200 m, 400 m, 600 m, 800 m and 1000 m are 100.0 m, 99.2 m, 101.0 m, 101.8 m, 101.4 m and 101.0 m respectively. The effective gradient of runway will be______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The capacity of parallel runway pattern depends upon______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  As per ICAO, for A, B, and C type of airports, maximum effective, transverse and longitudinal grades in percentage respectively are______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The length of runway under standard conditions is 2000 m. The elevation of airport site is 300 m. Its reference temperature is 33.05°C. If the runway is to be constructed with an effective gradient of 0.25 percent, the corrected runway length will be________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Zero fuel weight of an aircraft is_________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts