MCQs: A rolled steel joist is simply supported at its ends and carries a uniformly distributed load which causes a maximum deflection of 10 mm and slope at the ends of 0.002 radian. The length of the joist will be________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (f /N)s__________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm for an eccentric load 100 t for nondevelopment of tension, is__________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: In the truss shown in given figure, the force in member BD is______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: The moment of inertia of a circular section about any diameter D, is______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: Pick up the correct statement from the following__________.?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: Y are the bending moment, moment of inertia, radius of curvature, modulus of If M, I, R, E, F, and elasticity stress and the depth of the neutral axis at section, then________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: The locus of the moment of inertia about inclined axes to the principal axis, is______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: A steel plate d × b is sandwiched rigidly between two timber joists each D × B/2 in section. The steel will be (where Young’s modulus of steel is m times that of the timber)_________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: The general expression for the B.M. of a beam of length l is the beam carries M = (wl/2) x – (wx²/2)_______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: In the truss, the force in the member AC is_______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: The point of contraflexure is the point where_______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: d constant, the width of a cantilever of length l of uniform strength loaded with Keeping the depth a uniformly distributed load w varies from zero at the free end and________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: y/n) (1 – a l/r), is For calculating the allowable stress of long columns. The empirical formula 0 known as_________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: For determining the support reactions at A and B of a three hinged arch, points B and Care joined and produced to intersect the load line at D and a line parallel to the load line through A at D’. Distances AD, DD’ and AD’ when measured were 4 cm, 3 cm and 5 cm respectively. The angle between the reactions at A and B is___________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: The ratio of the maximum deflections of a simply supported beam with a central load W and of a cantilever of same length and with a load W at its free end, is________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: A square column carries a load P at the centroid of one of the quarters of the square. If a is the side of the main square, the combined bending stress will be________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: A material may fail if______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is____________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2, the deflection of the free end, is________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts
