|
MCQs: Design of a two way slab simply supported on edges and having no provision to prevent the corners from lifting, is made by_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: As per IS : 456, the reinforcement in a column should not be less than________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than____________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The advantage of reinforced concrete, is due to_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: An R.C.C. column is treated as short column if its slenderness ratio is less than_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The allowable tensile stress in mild steel stirrups, reinforced cement concrete, is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The thickness of the topping of a ribbed slab, varies between________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The angle of internal friction of soil mass is the angle whose_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the loading on a pre-stressed rectangular beam, is uniformly distributed, the tendon to be provided should be_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the maximum dip of a parabolic tendon carrying tension P is h and the effective length of the pre-stressed beam is L, the upward uniform pressure will be________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The steel generally used in R.C.C. work, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Pick up the assumption for the design of a pre-stressed concrete member from the following_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the ratio of long and short spans of a two way slab with corners held down is r, the actual reduction of B.M. is given by
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: By over-reinforcing a beam, the moment of resistance can be increased not more than________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A part of the slab may be considered as the flange of the T-beam if__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
