Process Equipment & Plant Design Mcqs for Chemical

Q.  (Le/D) for a Tee (used as elbow, entering branch) would be ____________________?

a. Less than that for Tee (used as elbow, entering run)
b. More than that for Tee (used as elbow, entering run)
c. Around 90
d. Both B. and C.


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  A shell may by termed as thin if its thickness to diameter ratio is less than 0.1. The factor which can be neglected in the calculation of membrane stresses is________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The average velocity in the tubes of a 1-4 heat exchanger is ______________ times that in 1-1 heat exchanger having the same size & number of tubes and operated at same liquid flow rate ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _____________ heat exchanger is also known as ‘hair pin type’ exchanger?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger, triangular pitch arrangement as compared to square pitch arrangement ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum tube pitch recommended for shell and tube heat exchangers is about _______________ times the outside diameter of the tube?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following efficiencies can be greater than 100% ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Angled baffles are preferred in the agitation tank to control the swirling action; if the viscosity of the liquid to be mixed is about 200 poise. However, the baffle may be completely eliminated for mixing liquids having viscosity above ____________________ poise?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the slope of the operating line in the rectifying section of a distillation column ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of lateral strain to linear strain is termed as the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Normal screwed fittings are used for pipes upto a diameter of _______________ inches?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio, (propeller agitator dia/tank dia) is normally taken as____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Tube height in a calandria type evaporator is normally less than _______________ metres?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Weep holes provided in the plates of a distillation column ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement about distillation operation__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement pertaining to ‘Horton sphere’ used for the storage of liquid ammonia ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement about the design of a sieve plate column ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement pertaining to the use of valve tray, seive tray and bubble cap trays in continuous distillation column ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the correct statement ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts