RCC Structures Design Mcqs


Q.  Lapped splices in tensile reinforcement are generally not used for bars of size larger than______________?

a. 18 mm diameter
b. 24 mm diameter
c. 30 mm diameter
d. 36 mm diameter


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The design of heel slab of a retaining wall is based on the maximum bending moment due to______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The neutral axis of a T-beam exists_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The minimum thickness of a flat slab is taken_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A pre-cast pile generally used, is______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In a pre-stressed member it is advisable to use________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Steel bars are generally connected together to get greater length than the standard length by providing_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  mutually perpendicular principal stresses acting on a soil mass, the normal stress If p1 and p2 are________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  carrying a uniformly distributed load per metre length is suspended at two A pile of length points, the maximum, B.M. at the centre of the pile or at the points of suspension, is_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If is the uniformly distributed load on a circular slab of radius maximum positive radial moment at its centre, is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  For M 150 grade concrete (1:2:4) the moment of resistance factor is_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The spacing of transverse reinforcement of column is decided by the following consideration_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The self-weight of the footing, is_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the bearing capacity of soil is 10 tonnes/cm2 and the projection of plain concrete footing from walls, is a cm, the depth D of footing is_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  After pre-stressing process is completed, a loss of stress is due to______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If R and T are rise and tread of a stair spanning horizontally, the steps are supported by a wall on one side and by a stringer beam on the other side, the steps are designed as beams of width_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If p1 and P2 are effective lateral loadings at the bottom and top exerted by a level earth subjected to a super-load on the vertical face of height h of a retaining wall, the horizontal pressure p per unit length of the wall, is____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The transverse reinforcements provided at right angles to the main reinforcement_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Long and short spans of a two way slab are l and l and load on the slab acting on strips parallel to lx and ly be wx and wy respectively. Accordingy to xRankine Grashoff theory___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm