Mechanical Operations Mcqs for Chemical

Q.  Kick’s law assumes that the energy required for size reduction is proportional to the logarithm of the ratio between the initial and the final diameters. The unit of Kick’s constant is_________________?

a. kW. sec/kg
b. kWh/kg
c. kWh/sec. kg
d. kg/sec


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  For raschig rings, the sphericity is_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In washing type plate and frame filter press, the ratio of washing rate to the final filtrate rate is__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pine oil and Cresylic acid are used as ______________ in the froth floatation process?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Energy requirement (per unit mass of material crushed/ground) is highest for__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Gold ore concentration is mostly done using___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Screw conveyors are________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A suspension of glass beads in ethylene glycol has a hindered settling velocity of 1.7 mm/s, while the terminal settling velocity of a single glass bead in ethylene glycol is 17 mm/s. If the Richardson-Zaki hindered settling index is 4.5, the volume fraction of solids in the suspension is_____________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Power consumption during turbulent flow in agitation tank is proportional to the ______________ of the liquid?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  200 mesh screen means 200 openings per_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following terminology is not used for size reduction of materials to fine sizes or powders ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The porosity of a compressible cake is _____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most common filter aid is_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _______________ mill is normally used for grinding of talc?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For achieving maximum capacity of the ball mill, the ball charge should be equal to about ______________ percent of the ball mill volume?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following can be most effectively used for clarification of lube oil and printing ink ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Mixer used for rubber compounding is__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Froth floatation is the most suitable for treating ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following must be stored in silos and not in open yard ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Sulphuric acid mist is arrested by using a ____________ scrubber?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts