Process Equipment & Plant Design Mcqs for Chemical

Q.  ____________ is the determining factor for the number of bubble caps to be used per tray?

a. Permissible slot velocity
b. Tray diameter
c. Liquid load
d. Vapor load


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Circumferential (hoop) stress in a thin cylindrical vessel under internal pressure is _____________ the longitudinal stress?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The optimum size ratio for two mixed reactors in series depends on the kinetics of the reaction and the conversion level. For reaction orders more than one, the_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For turbine agitator, the impeller diameter is about_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Commercial packed scrubbers are normally designed for a pressure drop range of ______________ mm water column per metre of packed height?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slope of operating line in the rectifying section of a distillation column is unity, if the reflux ratio is___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Overall mass transfer co-efficient in case of absorption of __________ in water is based on the gas film co-efficient only, as the mass transfer process is gas film (phase) controlling ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum baffle spacing recommended in a shell and tube heat exchanger is equal to _____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most common standard size of bubble caps used in industrial operation is___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Heat transfer co-efficient, hG(Kcal/hr.m2 .°C) and mass velocity of air, G (kg/hr.m2 ) for air flow parallel to the surface in case of constant drying rate in batch drying is related as hG = 0.0176G0.8. But when the flow of air perpendicular to the surface is encountered, this equation changes to ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Height equivalent to a theoretical plate (HETP) is the height of packing that will give the same separation as one theoretical plate in gas-liquid mass transfer operations like distillation, absorption/stripping and humidification/dehumidification. HETP which is experimentally determined, depends upon the_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid gradient over the tray results due to the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of tube length to shell diameter in case of liquid shell and tube heat exchanger ranges from__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slope of the feed line in distillation operation is given by (where, q = fraction of the feed stream that is liquid ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ____________ head is the most economical for cylindrical vessels designed for operating at high pressure (> 15 atm.)?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The testing pressure of storage tanks and pressure vessels designed as per Indian standard codes should be about ______________ times the design pressure?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following factors affect the pressure drop in a co-current gas-liquid absorption packed tower ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following packing materials provides for maximum mass transfer ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The absorption factor is defined as (where, S1 = slope of the equilibrium curve, S2 = slope of the operating line) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger, tube side _______________ of the mass velocity?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In sieve plate column, holes are drilled or punched in sizes ranging from 2.5 to 12 mm (5 mm being widely used). The hole pitch is normally ______________ times the hole diameter to give the required hole area?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts