|
MCQs: Which of the following is a scalar quantity ?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Coefficient of friction depends on__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If a body is lying on a plane whose inclination with the horizontal is less than the angle of friction, then___________________?
1) a force is required to move the body upwards
2) a force is required to move the body downward
3) the body will not be in equilibrium
The correct answer is?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A ladder of weight ‘w’ rests against a smooth vertical wall, and rests on rough horizontal ground, the coefficient of friction between the ladder and the ground being 1/4. The maximum angle of inclination of the ladder to the vertical, if a man of weight ‘w’ is to walk to the top of it safely, is tan’1 x, where x is___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The shape of a suspended cable for a uniformly distributed load over it is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A light rope is loaded with many equal weights at equal horizontal intervals. The points of suspension on the rope lie on a_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A ball moving on a smooth horizontal table hits a rough vertical wall, the coefficient of restitution between ball and wall being 1/3. The ball rebounds at the same angle. The fraction of its kinetic energy lost is___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A ball is dropped from a height of 16 m on a horizontal floor. If it rebounds to a height of 9 m after striking the floor, the coefficient of restitution between ball and floor is_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: When a body slides down an inclined surface, the acceleration of the body is given by__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A shell travelling with a horizontal velocity of 100 m/sec explodes and splits into two parts, one of mass 10 kg and the other of 15 kg. The 15 kg mass drops vertically downward with initial velocity of 100 m/sec and the 10 kg mass begins to travel at an angle to the horizontal of tan”1 x, where x is______________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A shell of mass 100 kg travelling with a velocity of 10 m/sec breaks into two equal pieces during an explosion which provides an extra kinetic energy of 20000 Joules. If the pieces continue to move in the same direction as before, then the speed of the faster one must be____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Two objects moving with uniform speeds are 5 m apart after 1 second when they move towards each other and are 1 m apart when they move in the same direction. The speeds of the objects are____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The angular speed of a car taking a circular turn of radius 100 m at 36 km/hr will be___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The condilion for a lifting machine to be reversible is that its efficiency should be_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a lifting machine with efficiency 60%, an effort of 200 N is required to raise a load of 6 kN. The velocity ratio of the machine is_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A system of copianar forces acting on a rigid body can be reduced to________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Force polygon method is applicable for_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The diagram showing the point of application and line of action of forces in their plane is called____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The bending moment in an arch is proportional to___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: An ordinate in a funicular polygon represents__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
