RCC Structures Design Mcqs

Q.  In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2, nominal reinforcement is provided at a pitch of________________?

a. One -half lever arm of the section
b. One-third lever arm of the section
c. Lever arm of the section
d. One and half lever arm of the section


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  As per IS : 456, the reinforcement in a column should not be less than________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than____________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The advantage of reinforced concrete, is due to_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  An R.C.C. column is treated as short column if its slenderness ratio is less than_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The allowable tensile stress in mild steel stirrups, reinforced cement concrete, is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The thickness of the topping of a ribbed slab, varies between________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The angle of internal friction of soil mass is the angle whose_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the loading on a pre-stressed rectangular beam, is uniformly distributed, the tendon to be provided should be_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the maximum dip of a parabolic tendon carrying tension P is h and the effective length of the pre-stressed beam is L, the upward uniform pressure will be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The steel generally used in R.C.C. work, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick up the assumption for the design of a pre-stressed concrete member from the following_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the ratio of long and short spans of a two way slab with corners held down is r, the actual reduction of B.M. is given by
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  By over-reinforcing a beam, the moment of resistance can be increased not more than________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A part of the slab may be considered as the flange of the T-beam if__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  per unit run exerted by the Total pressure on the vertical face of a retaining wall of height retained earth weighing per unit volume, is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts