|
MCQs: If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm 2, the angle of twist in radians, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A compound truss may be formed by connecting two simple rigid frames, by_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The ratio of crippling loads of a column having both the ends fixed to the column having both the ends hinged, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For determining the force in the member AB of the truss shown in the given figure by method of sections, the section is made to pass through AB, AD and ED and the moments are taken about___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The degree of indeterminacy of the frame in the given figure, is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A compound bar consists of two bars of equal length. Steel bar cross -section is 3500 mm2and that of brass bar is 3000 mm2. These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2, the stresses developed are___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The ratio of circumferential stress to the longitudinal stress in the walls of a cylindrical shell, due to flowing liquid, is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The forces acting on the bar as shown in the given figure introduce________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A simply supported beam carries varying load from zero at one end and w at the other end. If the length of the beam is a, the maximum bending moment will be_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The yield moment of a cross section is defined as the moment that will just produce the yield stress in_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A road of uniform cross-section A and length L force P. The Young’s Modulus E of the material, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The forces in the members of simple trusses, may be analysed by________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: P = / L² is the equation for Euler’s crippling load if_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If a three hinged parabolic arch, (span l, rise h) is carrying a uniformly distributed load w/unit length over the entire span__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The ratio of the stresses produced by a suddenly applied load and by a gradually applied load on a bar, is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Slenderness ratio of a long column, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The horizontal thrust on the ends of a two hinged semicircular arch of radius carrying_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A shaft subjected to a bending moment M and a torque T, experiences__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For calculating the allowable stress of long columns known as_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: P=4²EI/L² is the equation of Euler’s crippling load if________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
