VLSI Design & Technology Test Questions


Q.  In SM chart for UART transmitter, which state/s indicate/s the waiting of sequential machine for the rising edge of bit clock and the consequent clearing of low order bit of TSR in order to transmit logic '0' for one bit time?

a. IDLE State
b. Sync State
c. Transmit_Data_State
d. All of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Why is the use of mode buffer prohibited in the design process of synthesizer?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  If a port is declared as buffer, then which problem is generated in hierarchical design due to mapping with port of buffer mode of other entities only?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which UART component/s divide/s the system clock to provide the bit clock with the period equal to one bit time and Bclock x 8?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  In Gray coding, when the state machine changes state, ______ bit/s in the state vector changes the value.
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which type of CPLD packaging comprises pins on all four sides that wrap around the edges of chip?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  An antifuse element initial provides ______ between two conductors in absence of the application of sufficient programming voltage.
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  In spartan-3 family architecture, which programmable functional element accepts two 18 bit binary numbers as inputs and computes the product?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which level of routing resources are supposed to be the dedicated lines allowing output of each tile to connect directly to every input of eight surrounding tiles?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Maze routing is also known as ________
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Maze routing is used to determine the _______path for a single wire between a set of points, if any path exists.
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  In a chip, which type/s of pad design/s is/are adopted to solve the problem of pin count?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  The power consumption of static CMOS gates varies with the _____ of power supply voltage.
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which factor/s play/s a crucial role in determining the speed of CMOS logic gate?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  In CMOS circuits, which type of power dissipation occurs due to switching of transient current and charging & discharging of load capacitance?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  In accordance to the scaling technology, the total delay of the logic circuit depends on ______
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  In two-stage op-amp, what is the purpose of compensation circuitry?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  According to the principle of current mirror, if gate-source potentials of two identical MOS transistors are equal, then the channel currents should be _______
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  PSSR can be defined as the product of the ratio of change in supply voltage to change in output voltage of op-amp caused by the change in power supply & _______ of op-amp.
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the following serves as an input stage to most of the op-amps due to its compatibility with IC technology?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the following is/are responsible for the occurrence of 'Delay Faults'?
Category: Electronic Engineering Questions,   Published by: teswesm