Process Equipment & Plant Design Mcqs for Chemical

Q.  In hydrostatic testing of welded pipe (for leakage, strength etc.) the ratio of minimum hydrostatic test pressure to internal design pressure is around __________________?

a. 0.5
b. 1.5
c. 2.5
d. 3.5


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Wind load consideration in the design of a support can be neglected, when the vessel is___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Heat transfer co-efficient for a horizontal condenser as compared to a vertical condenser operating under similar conditions is_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For identical operating conditions, the pressure drop over _______________ tray is the highest out of the following?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger having square pitch, the shell side equivalent diameter is given by (where, P = pitch, d = outside diameter of the tube) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the allocated cap area, bubble caps are generally arranged on equilateral triangular pitch. Number of caps fixed on a plate is with a __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Baffle spacing is generally _________________ the I.D. of the shell ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The dust collection efficiency of a cyclone separator_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Log mean temperature difference in case of multi-pass shell and tube heat exchanger is always_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In distillation columns, bubble caps are held in place over trays by ________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The necessary wall thickness for a metallic storage vessel is a function of the ___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Cylindrical shell thickness of rotary drier is generally _______________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The length of straight rectangular weir used on cross-flow trays is generally ________________ the column diameter ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger, the clearance of the tube is generally___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Frame thickness in the plate and frame filter press is normally in the range of ______________ inches?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of saddle packing (e.g., berl and intralox saddles), the maximum size of the packing should not exceed ______________ of the column diameter?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  At the following point for a given packing and set of fluids, the pressure drop per metre of packed height, with variation in fluid rates and operating pressure____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a double pipe (concentric) heat exchanger, the hydraulic radius for heat transfer (for a fluid flowing through the annulus) would be_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A/an _______________ is used for changing the direction of a pipeline?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Low pressure steam (with saturation temperature between 105 to 120°C) is usually used in the vacuum evaporators, which normally employ a vacuum of about _______________ mm Hg (referred to a 760 mm mercury barometer)?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Elastic failure of a material occurs, when the tensile stress equals yield strength, yield point or the elastic limit. Also, the elastic failure occurs according to maximum strain theory, when the maximum tensile strain equals (where, ζ = yield strength and E = modulus of elasticity) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts