Chemical Engineering Basics Mcqs

Q.  In condensers used in thermal power plants, steam is normally used in shell side and cooling water on the tube side, because of the reason that ?

a. Compared to the mass flow rate of cooling water, the rate of condensation of steam is invariably smaller
b. Maintaining vacuum on tube side is more difficult than that on the shell side
c. Water velocity can be increased conveniently to increase the overall heat transfer co-efficient because of its lower specific volume compared to steam
d. Condenser can act as a storage unit for condensed steam


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Diamagnetic materials___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the value of included angle of a triangular notch for maximum discharge ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is a boiler accessory i.e., not a boiler mounting ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most important requirement for aluminium industry is the availability of cheap _______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Steel containing low percentage of nickel, chromium & tungsten are termed as the _____________ steel ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Materials having resistivity ranging from 1 to 100 ohm. cm is termed as___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Plasma is_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Heat flow across a hollow sphere of inner radius ‘r1’ and outer radius ‘r2’ is directly proportional to__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Tempering of a material does not improve its____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In connection with corrosion of metals, passivation is the process that__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  On oscilloscope screen for dynamic measurement, lissajous diagram is normally used to determine the ______________ of the input signal?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following forces does not act on a fluid at rest ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Cold cracking in the heat affected zone of a high strength steel weld can take place because of the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Moist climate is the most favourable factor in the site selection far a_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Powder metallurgy is used to produce__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Primary designation of steel is based on its__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Wohler test is a destructive test to find out the ___________________ strength of a prepared metal specimen ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The temperature at which ferromagnetic material can no longer be magnetized by the outside forces, is termed as the____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The two elements required to form substitutional solid solution should not have___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts