Mechanical Operations Mcqs for Chemical

Q.  In case of a hammer crusher, the final product size depends on the____________________?

a. Feed rate
b. Rotor speed
c. Clearance between hammer & grinding plates
d. All A., B. and C.


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  The unit of filter medium resistance is________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Bucket elevators are not suitable for the vertical lifting of __________ materials?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A cottrell precipitator makes use of the ______________ for dusty air cleaning?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following relationships between co-efficient of friction (μ) between rock & roll and a (half of the angle of nip) of the particle to be crushed is correct ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For raschig rings, the sphericity is_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In washing type plate and frame filter press, the ratio of washing rate to the final filtrate rate is__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pine oil and Cresylic acid are used as ______________ in the froth floatation process?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Energy requirement (per unit mass of material crushed/ground) is highest for__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Gold ore concentration is mostly done using___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Screw conveyors are________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A suspension of glass beads in ethylene glycol has a hindered settling velocity of 1.7 mm/s, while the terminal settling velocity of a single glass bead in ethylene glycol is 17 mm/s. If the Richardson-Zaki hindered settling index is 4.5, the volume fraction of solids in the suspension is_____________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Power consumption during turbulent flow in agitation tank is proportional to the ______________ of the liquid?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  200 mesh screen means 200 openings per_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following terminology is not used for size reduction of materials to fine sizes or powders ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The porosity of a compressible cake is _____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most common filter aid is_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _______________ mill is normally used for grinding of talc?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For achieving maximum capacity of the ball mill, the ball charge should be equal to about ______________ percent of the ball mill volume?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following can be most effectively used for clarification of lube oil and printing ink ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts