Process Equipment & Plant Design Mcqs for Chemical

Q.  In a shell and tube heat exchanger for a given heat transfer surface area, smaller diameter tubes are favoured as compared to larger diameter ones; because the smaller diameter tubes ______________?

a. Are easier to clean
b. Are less prone to fouling
c. Can be fitted into a smaller shell diameter hence the cost of the heat exchanger would be less
d. None of these


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Le/D) for 90° elbow (medium radius) and 90°square elbow would be respectively around___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum plate efficiency is achieved in case of ______________ flow?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Tubes are fixed to the tube sheet (a thick circular metallic plate) by the method of tube rolling and brazing (non-removable) or ferrule connection (removable). Thickness of the tube, sheet is normally ____________ the outside diameter of the tube but in no case it should be less than 22 mm (7/8″)?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a multiple effect evaporator system having ‘n’ effects, the amount of water evaporated per unit surface area in approximately equal to _____________ times that in a single effect?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Slope of counter-current flow rotary drier is in the range of ____________ meter/metre?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid gradient over a tray can be minimised by________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Ratio of tube length to shell diameter for a shell and tube heat exchanger is________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  (Le/D) for couplings and unions would be_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A shell may by termed as thin if its thickness to diameter ratio is less than 0.1. The factor which can be neglected in the calculation of membrane stresses is________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The average velocity in the tubes of a 1-4 heat exchanger is ______________ times that in 1-1 heat exchanger having the same size & number of tubes and operated at same liquid flow rate ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _____________ heat exchanger is also known as ‘hair pin type’ exchanger?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger, triangular pitch arrangement as compared to square pitch arrangement ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum tube pitch recommended for shell and tube heat exchangers is about _______________ times the outside diameter of the tube?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following efficiencies can be greater than 100% ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Angled baffles are preferred in the agitation tank to control the swirling action; if the viscosity of the liquid to be mixed is about 200 poise. However, the baffle may be completely eliminated for mixing liquids having viscosity above ____________________ poise?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the slope of the operating line in the rectifying section of a distillation column ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of lateral strain to linear strain is termed as the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Normal screwed fittings are used for pipes upto a diameter of _______________ inches?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio, (propeller agitator dia/tank dia) is normally taken as____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Tube height in a calandria type evaporator is normally less than _______________ metres?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts