Series parallel Circuits Mcqs


Q.  In a series–parallel circuit consisting of R1 and R2 in series and connected in parallel with R3, if R1 opens, then R2‘s voltage will:___________?

a. increase
b. remain the same
c. decrease
d. cannot tell


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  A certain circuit is composed of two parallel resistors. The total resistance is 1,403 Ω. One of the resistors is 2 kΩ. The other resistor value is____________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  A certain Wheatstone bridge has the following resistor values: R1 = 10 kΩ, R2 = 720 Ω, and R4 = 2.4 kΩ. The unknown resistance is_____________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  A 12 kΩ resistor, a 15 kΩ resistor, and a 22 kΩ resistor are in series with two 10 kΩ resistors that are in parallel. The source voltage is 75 V. Current through the 15 kΩ resistor is approximately___________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  A voltage divider consists of two 68 kΩ resistors and a 24 V source. The unknown output voltage is______________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  In a certain low-pass filter, fc = 3.5 kHz.if the input voltage is a 6 V sine wave with a dc level of 10 V, what is the output voltage magnitude?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  A parallel resonant band-pass filter consists of a 90 Ω resistor in series with a parallel network made up of a 60 mH coil and a 0.02 µF capacitor. The output is taken across the capacitor/coil. The coil winding has a resistance of 20 Ω. What is the center frequency of the filter?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  An RL high-pass filter consists of a 470 Ω resistor and a 600 mH coil. The output is taken across the coil. The circuit’s critical frequency is___________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  An RC low-pass filter consists of a 120 Ω resistor and a 0.002 µF capacitor. The output is taken across the capacitor. The circuit’s critical frequency is___________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  In a certain low-pass filter, fc = 3.5 kHz. Its pass-band is_______________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  An RC high-pass filter consists of an 820 Ω resistor. What is the value of C so that Xc is ten times less than Rat an input frequency of 12 kHz?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  In a series resonant band-pass filter, a lower value of Q results in______________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  The maximum output voltage of a certain low-pass filter is 15 V. The output voltage at the critical frequency is_____________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  The same signal in Problem 2 is applied to an RC high-pass filter. If the reactance is zero at the input frequency, the output voltage is____________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  A sinusoidal voltage with a peak-to-peak value of 18 V is applied to an RC low-pass filter. If the reactance at the input frequency is zero, the output voltage is____________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  Vout = 500 mV, and Vin = 1.3 V. The ratio Vout/ Vin expressed in dB is__________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  A parallel resonant band-pass filter consists of a 6.8 Ω resistor in series with a parallel network made up of an 8 µH coil and a 120 pF capacitor. The output is taken across the capacitor/coil. Assume RW = 0 Ω. What is the center frequency of the filter?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  In a certain low-pass filter, fc = 3.5 kHz. If the input voltage is a 6 V sine wave with a dc level of 10 V, what is the output voltage magnitude?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  An RL low-pass filter consists of a 5.6 mH coil and a 3.3 kΩ resistor. The output voltage is taken across the resistor. The circuit’s critical frequency is______________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  An RC high-pass filter consists of a 0.2 µF capacitor and a 220 Ω resistor. The output is taken across the resistor. The circuit’s critical frequency is_____________?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  At a certain frequency, the output voltage of a filter is 6 V and the input is 12 V. The voltage ratio in decibels is_____________?
Category: Electrical Engineering Questions,   Published by: teswesm