Railway Engineering Mcqs

Q.  In a scissors cross-over, the crossings provided are_________________?
i) 2 obtuse angle crossings
ii) 4 obtuse angle crossings
iii) 4 acute angle crossings
iv) 6 acute angle crossings
The correct answer is ?


a. (i) and (iii)
b. (i)and(iv)
c. (ii) and (iii)
d. (ii) and (iv)


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The slenderness ratio of a column supported throughout its length by a masonry wall is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The effective length of a battened strut effectively held in position at both ends but not restrained in direction is taken as________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  According to IS Specifications, the maximum pitch of rivets in compression is_____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum slenderness ratio of a steel column, the design of which is governed by wind or seismic forces is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  According to IS:800, in the Merchant Rankine formula the value of imperfection index (n) is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum slenderness ratio of a compression member carrying both dead and superimposed load is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  According to IS Specifications, the effective length of a column effectively held in position at both ends and restrained in direction at one end is taken as________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The actual thickness of butt weld as compared to the thickness of plate is usually________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For a standard 45° fillet, the ratio of size of fillet to throat thickness is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A circular column section is generally not used in actual practice because________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The best arrangement to provide unified behaviour in built up steel columns is by______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The use of tie plates in laced columns is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Angle of inclination of the lacing bar with the longitudinal axis of the column should preferably be between____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The effective length of a battened column is increased by_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slenderness ratio of lacing bars should not exceed________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Shear buckling of web in a plate girder is prevented by using________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum thickness of web in a plate girder, when the plate is accessible and also exposed to weather, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per IS : 800, for compression flange, the outstand of flange plates should not exceed________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Bearing stiffener in a plate girder is used to__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Gantry girders are designed to resist_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts