Design of Concrete Structures Mcqs


Q.  In a pile of length /, the points of suspension from ends for lifting it are located at______________?

a. 0.207 1
b. 0.25 /
c. 0.293 /
d. 0.333 /


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Cube strength of controlled concrete to be used for pretensioned and post-tensioned work respectively should not be less than__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Ultimate strength of cold drawn high steel wires_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  High carbon content in the steel causes_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Prestress loss due to friction occurs________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Most common method of prestressing used for factory production is________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The purpose of reinforcement in prestressed concrete is________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The maximum value of hoop compression in a dome is given by___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In a spherical dome subjected to concentrated load at crown or uniformly distributed load, the meridional force is always________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The effect of creep on modular ratio is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The recommended value of modular ratio for reinforced brick work is______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In T-shaped R C. retaining walls, the main reinforcement in the stem is provided on______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Select the correct statement _?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Select the incorrect statement _?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The effect of adding calcium chloride in concrete is________________? 1. to increase shrinkage 2. to decrease shrinkage 3. to increase setting time 4. to decrease setting time The correct answer is?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Examine the following statements ___________? 1. Factor of safety for steel should be based on its yield stress, 2. Factor of safety for steel should be based on its ultimate stress, 3. Factor of safety for concrete should be based on its yield stress, 4. Factor of safety for concrete should be based on its ultimate stress. The correct statements are
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In counterfort type retaining walls_____________? 1. the vertical slab is designed as a continuous slab 2. the heel slab is designed as a continuous slab 3. the vertical slab is designed as a cantilever 4. the heel slab is designed as a cantilever The correct answer is?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The main reinforcement in the toe of a T- shaped R C. retaining wall is provided on_______________? 1. top face parallel to the wall 2. top face perpendicular to the wall 3. bottom face paralleUo the wall 4. bottom face perpendicular to the wall The correct answer is ?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In a counterfort retaining wall, the main reinforcement is provided on the_______________? 1. bottom face in front counterfort 2. inclined face in front counterfort 3. bottom face in back counterfort 4. inclined face in back counterEort The correct answer is
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on_______________? 1. bottom face near counterfort 2. top face near counterfort 3. bottom face near centre of span 4. top face near centre of span The correct answer is
Category: Civil Engineering Mcqs,   Published by: teswesm