Process Equipment & Plant Design Mcqs for Chemical

Q.  In a multipass shell and tube heat exchanger, the shell side cross flow area does not depend upon______________________?

a. Baffle spacing
b. Clearance
c. Pitch
d. None of these


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  The normal range of velocity of steam in pipes is _________________________ m/sec?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The wall thickness for a large high pressure pipeline is determined by the consideration of the____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Compensation against openings in process vessels for giving inlet and outlet connections, for providing sight glasses and manholes etc. is provided for strength and rigidity. The most efficient type of compensation is of _______________ type?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Hazards associated with the relief valve leakage for extremely hazardous material storage can be taken care of by providing___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Lap joints are preferred for plates having thickness _______________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Thickness of the frame of a plate and frame filter as compared to that of plates is___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Tube side heat transfer co-efficient for turbulent flow of liquid through tubes is proportional to___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A high vapour velocity is required for high plate efficiency in a sieve plate column. The satisfactory value of operating vapor velocity for design purpose in sieve plate column is about _______________ percent of the flooding velocity?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Number of evaporators which can be used in service in a multiple effect evaporation system is limited by the__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The retention time of material in a rotary dryer depends upon its ______________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For given number of passes, pitch & tube diameter, the maximum number of tubes that can be accommodated in a shell of tripled inside diameter will be ____________ times?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Generally, elliptical dished heads____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Hold up of material in a operating rotary drier is in the range of___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ______________ of water makes it a widely used coolant in heat exchangers?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A head comprises of straight flange section, corner torus, section and central dished section. Crown radius and knuckle radius in a head is related respectively to the__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a distillation column, the minimum residence time for liquid in the downspout is about ______________ seconds?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pressure drop due to pipe fittings can be estimated by the equation, ΔP/ρ = 4f, (Le/D) (V2/2gc) where, Le = equivalent length of straight pipeline which will incur the same frictional loss as the fitting and D = diameter of the fitting. The value of (Le/D) (dimensionless) for 45° elbow and 180° close return bends would be respectively around______________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In which of the following evaporators, steam is fed inside the tube while the liquor is outside the tube ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ________________ liquor is best handled in a long tube vertical evaporator ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The equivalent diameter for pressure drop is _______________ that for heat transfer?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts