MCQs: If diameter of a reinforcement bar is d, the anchorage value of the hook is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: As per I.S. 456 – 1978, the pH value of water shall be_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: For M 150 mix concrete, according to I.S. specifications, local bond stress, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: foundation is assumed as The weight of a_____________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: If the diameter of longitudinal bars of a square column is 16 mm, the diameter of lateral ties should not be less than____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: In a combined footing if shear stress does not exceed 5 kg/cm2, the nominal stirrups provided are________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The maximum shear stress (q) in concrete of a reinforced cement concrete beam is_____________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: An R.C.C. column is treated as long if its slenderness ratio is greater than____________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The thickness of base slab of a retaining wall generally provided, is_____________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2, the share stirrups are provided for a distance from either end where, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Distribution of shear intensity over a rectangular section of a beam, follows_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: In a singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Design of R.C.C. simply supported beams carrying U.D.L. is based on the resultant B.M. at________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Design of R.C.C. cantilever beams, is based on the resultant force at______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Distribution reinforcement in a simply supported slab, is provided to distribute_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: If the size of a column is reduced above the floor, the main bars of the columns, are_____________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The minimum number of main steel bars provided in R.C.C________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: A short column 20 cm × 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2, the Safe load on the column, should not exceed_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: If T and R are tread and rise respectively of a stair, then_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|