Strength of Materials Test Questions


Q.  If three forces acting in one plane upon a rigid body, keep it in equilibrium, then they must either___________________?

a. meet in a point
b. be all parallel
c. at least two of them must meet
d. all the above are correct
e. none of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  A projectile is fired at an angle 9 to the vertical. Its horizontal range will be maximum when 9 is__________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Shear stress induced in a shaft subjected to tension will be__________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A key is subjected to side pressure as well at shearing forces. These pressures are called_________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The torsional rigidity of a shaft is expressed by the_______________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Longitudinal stress in a thin cylinder is__________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A boiler shell 200 cm diameter and plate thickness 1.5 cm is subjected to internal pressure of 1.5 MN/m , then the hoop stress will be_________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The deformation of a bar under its own weight compared to the deformation of same body subjected to a direct load equal to weight of the body is_______________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Rivets are made of following type of material_________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  If the rivets in adjacent rows are staggered and the outermost row has only one rivet, the arrangement of the rivets is called__________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A riveted joint in which every rivet of a row is opposite to other rivet of the outer row, is known as______________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Efficiency of a riveted joint is the ratio of its strength (max. load it can resist without failure) to the strength of the unpunched plate in_________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  In riveted boiler joints, all stresses, shearing, bearing and tensile are based on the_________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The ratio of elongation in a prismatic bar due to its own weight (W) as compared to another similar bar carrying an additional weight (W) will be _________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A beam is loaded as cantilever. If the load at the end is increased, the failure will occur ___________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The stress induced in a body due to suddenly applied load compared to when it is applied gradually is________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A material capable of absorbing large amount of energy before fracture is known as________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The total strain energy stored in a body is termed as__________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Resilience of a material is considered when it is subjected to_________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  When it is indicated that a member is elastic, it means that when force is applied, it will________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The internal reaction in bottom 80 cm length will be________________?
Category: Mechanical Engineering Questions,   Published by: teswesm