RCC Structures Design Mcqs


Q.  If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a__________________?

a. Simply supported beam
b. Continuous beam
c. Cantilever beam
d. None of these


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The minimum head room over a stair must be_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If q is the punching shear resistance per unit area a, is the side of a square footing for a column of side b, carrying a weight W including the weight of the footing, the depth D. of the footing from punching shear consideration, is____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the length of a combined footing for two columns l metres apart is L and the projection on the left side of the exterior column is x, then the projection y on the right side of the exterior column, in order to have a uniformly distributed load, is (where is the distance of centre of gravity of column loads______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the tendon is placed at an rectangular beam (sectional top edge)________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The Young’s modulus of elasticity of steel, is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Spacing of stirrups in a rectangular beam, is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Total pressure on the vertical face of a retaining wall of height h acts parallel to free surface and from the base at a distance of_____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  For initial estimate for a beam design, the width is assumed__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A pre-stressed rectangular beam which carries two concentrated loads W at L/3 from either end, is provided with a bent tendon with tension P such that central one-third portion of the tendon remains parallel to the longitudinal axis, the maximum dip h is_____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Design of a two way slab simply supported on edges and having no provision to prevent the corners from lifting, is made by_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  As per IS : 456, the reinforcement in a column should not be less than________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The advantage of reinforced concrete, is due to_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  An R.C.C. column is treated as short column if its slenderness ratio is less than_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The allowable tensile stress in mild steel stirrups, reinforced cement concrete, is_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The thickness of the topping of a ribbed slab, varies between________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The angle of internal friction of soil mass is the angle whose_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the loading on a pre-stressed rectangular beam, is uniformly distributed, the tendon to be provided should be_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm