Strength of Materials Test Questions

Q.  If the effective length of a column is twice the actual length, then the column is ________

a. fixed at both the ends
b. hinged at both the ends
c. fixed at one end and free at the other end
d. fixed at one end and hinged at the other end


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  A cylindrical roller bearing is subjected to frictional torque of 500 N-mm. What is the approximate power loss if the shaft rotates at 1500 r.p.m?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The expected rating life of roller bearings rotating at 1000 r.p.m. is 30000 hours and equivalent dynamic load of 4000 N acts on it. What is the basic dynamic capacity of the bearing?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the effect of large diametral quotient on worm and worm wheel?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A standard worm gear pair is designated as 4/40/10/8, what does number 10 in it indicate?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A worm gear pair is designated as 1/30/10/8. What is the face width of the worm gear?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following belts is used when axes of two shafts are perpendicular and intersecting?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Friction ply used in multiple-ply belts is made of ___________
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Two pulleys of an open belt drive A and B transmit power of 100 kW from pulley A running at 1000 r.p.m to pulley B at 500 r.p.m. If diameter of pulley A is 150 mm and 3% is the slip at operating conditions then what is the diameter of pulley B? (Assume thickness of belt = 12 mm)
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A flat belt pulley has centre distance between two pulleys as 1000 mm. If diameters of two pulleys are 600 mm and 300 mm, what is the length of belt?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the shear stress in fluid per unit velocity gradient called as?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following is not a property of lubricants?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Mass of ___________ required to neutralize one gram of lubricating oil is called as neutralization number.
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following gear tooth failures is/are induced when maximum Hertz contact stress on gear tooth surface exceeds surface endurance strength of tooth?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is Scuffing?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Angle made by ________ with axis of rotation is called as helix angle.
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the minimum face width required for a helical gear which has helix angle of 23° and normal module of 7?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  To avoid interference the minimum number of teeth required on helical pinion decreases as helix angle ________
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following statements is/are true?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A bevel gear has pitch circle diameters of pinion and gear as 20 mm and 40 mm respectively. What is the face width of bevel gear? (m =module)
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the pitch line velocity if pinion has pitch circle diameter of 35 mm and rotates at 1000 r.p.m transmitting power of 250 kW to the gear?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts