|
MCQs: The number of treads in a flight is equal to_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The shear reinforcement in R.C.C. is provided to resist__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2, the area of steel required, is___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The amount of reinforcement for main bars in a slab, is based upon___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The minimum cube strength of concrete used for a pre-stressed member, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by_____________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: effective depth and depth of the neutral axis respectively of a singly reinforced If d and n are the beam, the lever arm of the beam, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: bending moment of a simply supported slab is M Kg.cm, the effective depth of the If the maximum slab is (where Q is M.R. factor)________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The width of the flange of a T-beam, which may be considered to act effectively with the rib depends upon____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Pick up the true statement from the following?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Pick up the correct statement from the following_?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Dimensions of a beam need be changed if the shear stress is more than_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The effective width of a column strip of a flat slab, is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: As the percentage of steel increases________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For a number of columns constructed in a rcjw, the type of foundation provided, is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the modular ratio is , steel ratio is and overall depth of a beam is , the depth of the critical neutral axis of the beam, is___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a simply supported slab, alternate bars are curtailed at________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
