Process Equipment & Plant Design Mcqs for Chemical

Q.  Hoop (circumferential) stress induced in a thin walled ‘Horton Sphere’ used for the storage of liquid ammonia under pressure is____________________?

a. pD/2T
b. pD/4T
c. pD/3T
d. pD/6T


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Souders Brown equation given by, U = Kv √(ρl – ρv)/ρv, is used for the calculation of the ______________ in a continuous distillation column?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio for the rate of washing to the final rate of filtration in a washing type of plate and frame filter is____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Optimum economic pipe diameter for fluid flow is determined by the____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For annular flow of a fluid, the ratio of the equivalent diameter for pressure drop calculation to the equivalent diameter for heat transfer calculation is_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Seamless pipe is made________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A minimum clearance of about _______________ mm is maintained between the distillation column wall and the bubble cap?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum acceptable total liquid gradient over a tray is about _______________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Diameter of the sieve tray column is determined by the_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Le/D) for 90° elbow (medium radius) and 90°square elbow would be respectively around___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum plate efficiency is achieved in case of ______________ flow?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Tubes are fixed to the tube sheet (a thick circular metallic plate) by the method of tube rolling and brazing (non-removable) or ferrule connection (removable). Thickness of the tube, sheet is normally ____________ the outside diameter of the tube but in no case it should be less than 22 mm (7/8″)?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a multiple effect evaporator system having ‘n’ effects, the amount of water evaporated per unit surface area in approximately equal to _____________ times that in a single effect?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Slope of counter-current flow rotary drier is in the range of ____________ meter/metre?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid gradient over a tray can be minimised by________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Ratio of tube length to shell diameter for a shell and tube heat exchanger is________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  (Le/D) for couplings and unions would be_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A shell may by termed as thin if its thickness to diameter ratio is less than 0.1. The factor which can be neglected in the calculation of membrane stresses is________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The average velocity in the tubes of a 1-4 heat exchanger is ______________ times that in 1-1 heat exchanger having the same size & number of tubes and operated at same liquid flow rate ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _____________ heat exchanger is also known as ‘hair pin type’ exchanger?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger, triangular pitch arrangement as compared to square pitch arrangement ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts