Process Equipment & Plant Design Mcqs for Chemical

Q.  Heat transfer co-efficient for a horizontal condenser as compared to a vertical condenser operating under similar conditions is_______________?

a. Same
b. Less
c. About 3 times
d. About 0.33 times


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  _____________ shaped roof is the most commonly used roof for cylindrical storage tanks?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Filtration rate is affected by the________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Normally, the length to diameter ratio of rotary dryers varies from 4 to 10 and for its economic operation; the number of transfer units (NTU) for such dryers varies from ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of volumes of the mixed reactor to the plug flow reactor (for identical feed composition, flow rate, conversion, and for all positive reaction orders) is always ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a _____________ riveted joint, the number of rivets decreases from the innermost row to the outermost row?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A binary liquid Azeotropic mixture has boiling point lower than either of the components, when it shows _____________ deviation from Raoult’s Law?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The clearance between two tubes in a shell and tube heat exchanger is known as ‘ligament’, whose minimum value is _____________ the outside diameter of the tube, but in no case it should be less than 4.5 mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is the most common type of baffle used in industrial shell and tube heat exchanger ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ____________ is the determining factor for the number of bubble caps to be used per tray?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The buckling tendency of compression members is always in the direction of the _____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The equivalent diameter for fluid flow through a channel of constant non-circular cross section of area ‘A’ is given by (where, P = perimeter of the channel in contact with the fluid) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Accidents in chemical plants are mostly due to___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid redistribution should be done in a packed tower packed with raschig rings every 6 metres or ______________ times the column diameter, whichever is lower?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of linear stress to linear strain is termed as the ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A perforated plate has holes of diameter dn arranged in a pitch ph. Each hole has a tube of I.D. dt passing through it. The ligament efficiency is given by_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The thermal stress in a metallic bar does not depend upon the_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Diameter of rivet hole (d, mm) and the plate thickness (t, mm) are related by Unwin’s formula as___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Steam is preferred to be used as a heating medium in heat exchangers, because of its_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Poisson’s ratio of a material is the ratio of unit lateral strain to the unit axial elongation within its elastic limit. The value of Poisson’s ratio for structural and pressure vessel steel may be taken as ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts