Process Equipment & Plant Design Mcqs for Chemical

Q.  For pipe flows, head is proportional to ______________ at constant capacity (where D = pipe diameter) ?

a. 1/D
b. 1/D2
c. 1/D5
d. D2


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  For a given design of bubble cap, the number of bubble caps to be used per tray is set by the _________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A pipe is generally made of circular cross-section, because a circular cross-section has the____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the case of a shell and tube heat exchanger, the logarithmic mean temperature difference ______________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum size of the raschig rings used in a packed tower is about _______________ of the column diameter?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Width and depth of grooves in the tube sheet holes normally are _______________ inch respectively?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The shell side pressure drop in a shell and tube heat exchanger is maximum for _______________ baffle?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Equivalent diameter for heat transfer calculation for a duct of square cross-section having each side as ā€˜dā€™ will be__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Friction factor for turbulent flow in a new pipe is given by____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  To keep the power input constant for a stirred vessel operating under fully developed turbulent flow conditions (constant power number), if the impeller diameter is increased by 20%, the impeller speed should be decreased by a factor of_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Triangular pitch tube layout as compared to square pitch in a shell and tube heat exchanger________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Smaller sized packings are generally dumped to the packed columns, and the large ones of size greater than ______________ mm are stacked individually, which provides better control over bed porosity and offers lower gas pressure drop?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ends of a cylindrical vessel can be closed by a head, which can be one of the four shapes. For the same thickness, choose the one which can withstand the highest pressure ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A stuffing box is used for____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of shear stress to shear strain is called ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of a shell and tube heat exchanger, the minimum shell thickness for carbon steel (inclusive of corrosion allowance) depends on shell diameter and is in the range of ________________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _____________________ tray arrangement is recommended for distillation column having diameter upto 4 ft ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of bubble cap distillation column of diameter greater than 1.2 metres, the cap diameter is roughly about _______________ cms?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Wall thickness of schedule 40 pipe as compared to that of schedule 80 pipe is ___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Speed of the drum of the rotary vacuum filter normally ranges from _____________ rpm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a continuous distillation column, the optimum reflux ratio ranges from _______________ times the minimum reflux ratio?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts