Airport Engineering Mcqs


Q.  For determining the basic runway.length, the landing case requires that aircraft should come to a stop within p % of the landing distance. The value of p is________________?

a. 40 %
b. 50%
c. 60%
d. 75%


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The width and interval of transverse centre line bars along the extended centre line of runway, in approach lighting system are_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  According to ICAO, all markings on the runways are___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Calm period is the percentage of time during which wind intensity is less than______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The cruising speed of the aircraft is 500 kmph. If there is a head wind of 50 kmph, then the air speed and ground speed of the aircraft respectively will be_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  As per ICAO, the minimum basic runway length for A and E type of airport will be________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The length of clear zone for none instrument runway of a small aircraft is________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Consider the following statements regarding iCAO recommendation for correction to basic runway length_________________? 1. The basic runway length should be increased at the rate of 7 percent per 300 m rise in elevation above the mean sea level 2. The basic runway length after having been corrected for elevation should be further increased at the rate of 1 percent for every 1°C rise in airport reference temperature above the standard atmospheric temperature at that elevation 3. The runway length after having been corrected for elevation and temperature should be further increased at the rate of 20% for every 1 percent of effective gradient Select the correct statment
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Assertion A : The ratio of arriving and departing aircrafts influences the airport capacity: Reason R :Landing operation is generally given priority over the taking off operation_________________? Select your answer based on the coding system given below?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Malleability of a material can be defined as ______________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Mild steel belongs to the following category___________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Stress relaxation is- the phenomenon ___________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Isotropic materials are those which have the same ____________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The ability of a material to resist softening at high temperature is known as____________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The ultimate tensile strength and yield strength of most of the metals, when temperature falls from 0 to l00°C will _________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Points of arrest for iron correspond to__________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A material is known as allotropic or polymorphic if it __________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Which of the following constituents of steels is softest and least strong ________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The temperature at which ferromagnetic alpha iron transforms to paramagnetic alpha iron is _______________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Ferromagnetic alpha iron exists in temperature range of________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A reversible change in the atomic structure of steel with corresponding change in the properties is known as___________________?
Category: Mechanical Engineering Questions,   Published by: teswesm