Dock & Harbor Engineering Mcqs

Q.  For designing the dock, the proportion of ship load assumed to be borne by keel blocks is________________?

a. 5/8
b. 3/8
c. 3/16
d. 5/16


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Consider the following statements? (i) Fender is the cushion provided on the face of the jetty for ships to come in contact, (ii) Slip is the space of water area between two adjacent piers where ships are berthed, (iii) Pier head is a structure constructed near the tip of a break water near the harbour entrance. select the correct statements?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  An airport has 4 gates. If the weighted average gate occupancy time is 30 minutes and gate utilisation factor is 0.5, then the capacity of the gate will be___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The engine failure case for determining the basic runway length may require________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the monthly mean of average daily temperature for the hottest month of the year is 25° C and the monthly mean of the maximum daily temperature of the same month of the year is 46° C, the airport reference temperature is____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per ICAO recommendation, the rate of change of longitudinal gradient per 30 m length of vertical curve for A and B type of airports is limited to a maximum of__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per International Civil Aviation Organization (ICAO) recommendation, minimum width of safety area for instrumental runway should be_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The minimum width of clearway is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The total length of a runway is 1000 m. The elevation at distance 0,200 m, 400 m, 600 m, 800 m and 1000 m are 100.0 m, 99.2 m, 101.0 m, 101.8 m, 101.4 m and 101.0 m respectively. The effective gradient of runway will be______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The capacity of parallel runway pattern depends upon______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per ICAO, for A, B, and C type of airports, maximum effective, transverse and longitudinal grades in percentage respectively are______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The length of runway under standard conditions is 2000 m. The elevation of airport site is 300 m. Its reference temperature is 33.05°C. If the runway is to be constructed with an effective gradient of 0.25 percent, the corrected runway length will be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Zero fuel weight of an aircraft is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per ICAO, for airports serving big aircrafts, the crosswind component should not exceed_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For determining the basic runway.length, the landing case requires that aircraft should come to a stop within p % of the landing distance. The value of p is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Runway threshold is indicated by a series of parallel lines starting from a distance of_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In Intrumental landing system, the middle markers are located___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The centre to centre spacing of heliport lighting along the periphery of landing and take off area should be______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Assertion A: The width of a taxiway is smaller than the runway width. Reason R : The speed of the aircraft on a taxiway is greater than that on runway.? Select your answer based on coding system given below
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per UK design criteria, if LCN of aircraft is between 1.25 to 1.5 times the LCN of pavement, then the number of movements allowed are__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slope of the transitional surface for A, B and C type of runway shall be_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts