Digital Signal Processing Test Questions

Q.  For a partial fraction method to be followed,

1) The degree of the numerator must be more than the degree of the denominator.
2) The factors formed for partial fraction are a combination of Linear factors and Irreducible quadratic factors.
3) The degree of the numerator must be less than the degree of the denominator.
4) The factors formed for partial fraction are a combination of Linear factors and Square roots.


a. 1, 2 and 3 are correct
b. 1 and 2 are correct
c. 2 and 3 are correct
d. All the four are correct


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Discrete cosine transforms (DCTs) express a function or a signal in terms of
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  A system is said to be unstable if
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  A system is said to be marginally unstable if
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  The nonlinear difference equations are solved using
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  Correlation is used for 1) Computation of average power in waveforms 2) Climatography 3) Identification of binary code word in PCM systems 4) Quantization
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  The Chebyshev filters have 1) Flat pass band 2) Flat stop band 3) Equiripple pass band 4) Tapering stop band
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  The Elliptic filters have 1) Flat pass band 2) Flat stop band 3) Equiripple pass band 4) Equiripple stop band
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  The effects caused due to finite word lengths are 1) Coefficient quantization error 2) Adder overflow limit cycle 3) Round off noise 4) Limit cycles
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  The error in the filter output that results from rounding or truncating calculations within the filter is called
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  Consider the assertions given below. Which among them is an advantage of FIR Filter?
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  In FIR filter design, which among the following parameters is/are separately controlled by using Kaiser window?
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which window function is also regarded as 'Raised-cosine window'?
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  In Barlett window, the triangular function resembles the tapering of rectangular window sequence _______ from the middle to the ends.
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  In Gibb's phenomenon, the ringing effect is predominantly present near the ______ .
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  How is/are the roundoff errors reduced in the digital FIR filter?
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  In linear phase realization, equal valued coefficients are taken common for reducing the requisite number of ________.
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which filters exhibit their dependency upon the system design for the stability purpose?
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  In FIR filters, which among the following parameters remains unaffected by the quantization effect?
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  In the frequency response characteristics of FIR filter, the number of bits per coefficient should be _________in order to maintain the same error.
Category: Electronic Engineering Questions,   Published by: T-Code Scripts
MCQs:  In cascade form of realization, how many bits should be used to represent the FIR filter coefficients in order to avoid the quantization effect on filter coefficients?
Category: Electronic Engineering Questions,   Published by: T-Code Scripts