Design of Concrete Structures Mcqs


Q.  For a continuous slab of 3 m x 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is__________________?

a. 50 mm
b. 75 mm
c. 100 mm
d. 120 mm


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Maximum distance between expansion joints in structures as per IS : 456 – 1978 is________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A higher modular ratio shows____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Ratio of permissible stress in direct compression and bending compression is______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In working stress design, permissible bond stress in the case of deformed bars is more than that in plain bars by_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Half of the main steel in a simply supported slab is bent up near the support at a distance of x from the center of slab bearing where x is equal to________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the size of panel in a flat slab is 6m x 6m, then as per Indian Standard Code, the widths of column strip and middle strip are__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The permissible diagonal tensile stress in reinforced brick work is_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  When shear stress exceeds the permissible limit in a slab, then it is reduced by____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The main reason for providing number of reinforcing bars at a support in a simply supported beam is to resist in that zone_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The limits of percentage p of the longitudinal reinforce-ment in a column is given by_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The minimum cover to the ties or spirals should not be less than________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Maximum percentage reinforcement in case of slabs is limited to___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The diameter of ties in a column should be_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The minimum diameter of longitudinal bars in a column is________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  For the design of retaining walls, the minimum factor of safety against overturning is taken as_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The load carrying capacity of a helically reinforced column as compared to that of a tied column is about________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Due to circumferential action of the spiral in a spirally reinforced column________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following R.C. retaining walls is suitable for heights beyond 6m ?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine’s theory_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm