MCQs: A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net settlement (i.e. total settlement minus rebound) per tonne of test load should not exceed________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: An intermediate Tbeam reinforced with two layers of tensile steel with clear cover 13 cm encasted with the floor of a hall 12 metres by 7 metres, is spaced at 3 metres from adjoining beams and if the width of the beam is 20 cm, the breadth of the flange is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: The diameter of main bars in R.C.C. columns, shall not be less than________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: Based on punching shear consideration, the overall depth of a combined footing under a column A, is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: In a combined footing if shear stress exceeds 5 kg/cm2, the nominal stirrups provided are______________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: If W is the load on a circular slab of radius R, the maximum circumferential moment at the centre of the slab, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: The weight of reinforced concrete, is generally taken as______________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: A retaining wall and is the horizontal earth pressure, the factor of safety If is weight of against sliding, is_____________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: In a beam the local bond stress Sb, is equal to_______________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: With usual notations the depth of the neutral axis of a balanced section, is given by______________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2, the length of the beam having nominal reinforcement, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: If the length of a wall on either side of a lintel opening is at least half of its effective span L, the load W carried by the lintel is equivalent to the weight of brickwork contained in an equilateral triangle, producing a maximum bending moment____________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: The section of a reinforced beam where most distant concrete fibre in compression and tension in steel attains permissible stresses simultaneously, is called_________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: An underreinforced section means_________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or____________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: In a doublyreinforced beam if and the effective depth and is depth of critical neutral axis, the following relationship holds good______________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: The system in which high tensile alloy steel bars (silica manganese steel) are used as prestressing tendons, is known as________________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: The angle of repose of a soil is the maximum angle which the outer face of the soil mass makes_______________?
Category: Civil Engineering Mcqs, Published by: teswesm

MCQs: A raft foundation is provided if its area exceeds the plan area of the building by______________?
Category: Civil Engineering Mcqs, Published by: teswesm
