Strength of Materials Test Questions


Q.  Flow stress corresponds to___________________?

a. fluids in motion
b. breaking point
c. plastic deformation of solids
d. rupture stress
e. none of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  If three forces acting in one plane upon a rigid body, keep it in equilibrium, then they must either___________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The co-efficient of friction depends upon _________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Which of the following is the locus of a point that moves in such a manner that its distance from a fixed point is equal to its distance from a fixed line multiplied by a constant greater than one_______________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A sample of metal weighs 219 gms in air, 180 gms in water, 120 gms in an unknown fluid. Then which is correct statement about density of metal__________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The C.G. of a plane lamina will not be at its geometrical centre in the case of a __________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The M.I. of hollow circular section about a central axis perpendicular to section as compared to its M.I. about horizontal axis is________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The angle which an inclined plane makes with the horizontal when a body placed on it is about to move down is known as angle of __________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A body moves, from rest with a constant acceleration of 5 m per sec. The distance covered in 5 sec is most nearly_______________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  In actual machines_____________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A cable with a uniformly distributed load per horizontal metre run will take the following shape_________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Which of the following is the example of lever of first order__________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The C.G. of a right circular solid cone of height h lies at the following distance from the base________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The C.G. of a solid hemisphere lies on the central radius 3r_________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A flywheel on a motor goes from rest to 1000 rpm in 6 sec. The number of revolutions made is nearly equal to_________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  If n = number of members andy = number of joints, then for a perfect frame, n =________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The necessary condition for forces to be in equilibrium is that these should be_____________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The maximum frictional force which comes into play when a body just begins to slide over another surface is called________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A single force and a couple acting in the same plane upon a rigid body_________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A particle inside a hollow sphere of radius r, having coefficient of friction -rr can rest upto height of___________________?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The effort required to lift a load W on a screw jack with helix angle a and angle of friction
Category: Mechanical Engineering Questions,   Published by: teswesm