Process Equipment & Plant Design Mcqs for Chemical


Q.  Filtration rate is affected by the________________?

a. Pressure drop across the cake & filter medium
b. Cake & filter medium resistance
c. Area of filtering surface & the viscosity of filtrate
d. All A., B. and C.


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  In a rotary drier, the average retention time of solid is (where Z = length of the drier, metres ρ = apparent solid density, kg/m3 L = flow rate of dry solids, kg/see. m2 drier crosssection H = hold up of solid.) ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Optimum reflux ratio in a continuous distillation column is determined by the__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Bubble cap diameter used for the distillation column having diameter ranging from 1.5 to 4.5 metres is about ______________ mm?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Thin spherical shells subjected to internal pressure, develop ______________ stresses?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  A single pass air heater is connected to a two pass unit. For the air flow rate and other conditions remaining the same, the film heat transfer co-efficient for air will vary in the ratio of_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  A cylindrical pressure vessel of volume 6 πm3 has to be designed to withstand a maximum internal pressure of 10 atm. The allowable design stress of the material is 125N/mm2 and corrosion allowance is 2 mm. The thickness of the vessel for a length/diameter ratio of 3 will be close to________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The ratio of down take area to cross-sectional area of the tube, for calandria type evaporator ranges from_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The thickness of heat transfer plates used in the plate type heat exchanger ranges from _____________ mm, pressed in a single piece provided with grooves & corrugations?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Circumferential (hoop) stress in a thin cylindrical vessel under internal pressure is _____________ the longitudinal stress?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The optimum size ratio for two mixed reactors in series depends on the kinetics of the reaction and the conversion level. For reaction orders more than one, the_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  For turbine agitator, the impeller diameter is about_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Commercial packed scrubbers are normally designed for a pressure drop range of ______________ mm water column per metre of packed height?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The slope of operating line in the rectifying section of a distillation column is unity, if the reflux ratio is___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Overall mass transfer co-efficient in case of absorption of __________ in water is based on the gas film co-efficient only, as the mass transfer process is gas film (phase) controlling ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Minimum baffle spacing recommended in a shell and tube heat exchanger is equal to _____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The most common standard size of bubble caps used in industrial operation is___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Heat transfer co-efficient, hG(Kcal/hr.m2 .°C) and mass velocity of air, G (kg/hr.m2 ) for air flow parallel to the surface in case of constant drying rate in batch drying is related as hG = 0.0176G0.8. But when the flow of air perpendicular to the surface is encountered, this equation changes to ____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Height equivalent to a theoretical plate (HETP) is the height of packing that will give the same separation as one theoretical plate in gas-liquid mass transfer operations like distillation, absorption/stripping and humidification/dehumidification. HETP which is experimentally determined, depends upon the_______________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Liquid gradient over the tray results due to the___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The ratio of tube length to shell diameter in case of liquid shell and tube heat exchanger ranges from__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm