Chemical Engineering Basics Mcqs

Q.  Dislocation cross-slip is difficult in those materials, which have___________________?

a. Large number of slip systems
b. High work hardening rate
c. Coarse grain size
d. Low stacking fault energy


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Normalising of a casting does not__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Limestone addition in the blast furnace is done to flux _______________ present in the raw materials?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of brasses, with decreasing zinc percentage and increasing copper percentage, its _____________ increases ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Metallic surveying tapes are made of _____________ which has a low co-efficient of expansion & enough strength ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Titanium is produced by ___________________ of Ti Cl4 ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Atomic _______________ is a whole number for an element?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Out of the following, the lowest packing of atoms exists in ____________________ crystal lattice structure?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  An abrupt and sudden fall in the reading of barometer is an indication of the____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For the Stoke’s law to be valid in the case of a falling sphere in a fluid, the_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Saturated steam at a pressure of 25 kg/cm2 is throttled to attain 5 kg/cm2. Then the outcoming steam will be_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is resistant to the action of both heat & chemicals ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The kinematic viscosity (in stoke) and the absolute/dynamic viscosity (in poise) are the same for ______________ at room temperature ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ______________ wire is never used for making the heating element ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The heat released by cooling one mole of copper from 400 K to room temperature (300 K) is (assume : Cp of copper is 23 J K-1mole-1) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most suitable material for die casting is __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a totally irreversible isothermal expansion process for an ideal gas, ΔE = 0, ΔH = 0. Then ΔQ and ΔS will be_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following materials does not form adherent oxide film on surface ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The emf of a Deniell cell “Zn | Zn2+ || Cu2+ | Cu” can be increased by_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Lead is poured into the joint between two ______________ pipes?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts