Design of Concrete Structures Mcqs

Q.  Diagonal tension in a beam______________?

a. is maximum at neutral axis
b. decreases below the neutral axis and increases above the neutral axis
c. increases below the neutral axis and decreases above the neutral axis
d. remains same


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Ratio of permissible stress in direct compression and bending compression is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In working stress design, permissible bond stress in the case of deformed bars is more than that in plain bars by_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Half of the main steel in a simply supported slab is bent up near the support at a distance of x from the center of slab bearing where x is equal to________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the size of panel in a flat slab is 6m x 6m, then as per Indian Standard Code, the widths of column strip and middle strip are__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The permissible diagonal tensile stress in reinforced brick work is_____________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When shear stress exceeds the permissible limit in a slab, then it is reduced by____________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The main reason for providing number of reinforcing bars at a support in a simply supported beam is to resist in that zone_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The limits of percentage p of the longitudinal reinforce-ment in a column is given by_____________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The minimum cover to the ties or spirals should not be less than________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum percentage reinforcement in case of slabs is limited to___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The diameter of ties in a column should be_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The minimum diameter of longitudinal bars in a column is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For the design of retaining walls, the minimum factor of safety against overturning is taken as_____________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The load carrying capacity of a helically reinforced column as compared to that of a tied column is about________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Due to circumferential action of the spiral in a spirally reinforced column________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following R.C. retaining walls is suitable for heights beyond 6m ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine’s theory_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Modulus of elasticity of steel as per IS : 456-1978 shall be taken as______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the depth of neutral axis for a singly reinforced rectangular section is represented by kd in working stress design, then the value of k for balanced section_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts